$13Reg.$19
3PVP-AD:
Appliance Adapter -
Use to attach to appliance outlet allowing for easy pipe connection.
Seal adapter to appliance with high temperature sealant.
|
$28Reg.$32
3PVP-12:
Features fully unitized, twist-lock construction in 3” and 4”
diameters. Listed at 1” clearance to combustibles in the USA and
Canada. It can be used in both vertical and horizontal installations.
Stainless steel welded seam inner wall, combined with a galvalume
welded seam outer wall. Pipe OD is diameter plus 5⁄8”. Galvalume or
painted black outer finish. 12” length available with stainless steel
outer (SS). To calculate installed length, subtract 1 1⁄2” from each
length of pipe.
|
$38Reg.$42
3PVP-12A:
Use to add length to PelletVent Pro pipe. 12” pipe adds 3”-10” of
length, 18” pipe adds 3”-16” of length, when used with rigid sections
of pipe. Galvalume or painted black outer finish
|
$49Reg.$55
3PVP-E45:
Offsets obstructions as needed. Elbows swivel 360° at base. Angle not
adjustable.
|
$64Reg.$69
3PVP-E90:
Offsets obstructions as needed. Elbows swivel 360° at base. Angle not
adjustable.
|
$85Reg.$91
3PVP-T:
Use for a 90° offset. Branch swivels for alignment. Removeable
twist-lock Clean-Out Tee Cap.
|
$47Reg.$55
3PVP-VC:
Use for vertical installations only. Required where pipe terminates
above the roof line.
|
$32Reg.$37
3PVP-HC:
Use for horizontal terminations only. The Horizontal Cap can be turned
at the gore to direct exhaust output. Designed to create a
venturi effect to force exhaust out. Made of a laser-welded,
super-ferritic stainless steel inner wall that is scientifically proven
to resist corrosion from corn and other biofuels. Outer wall made of
laser-welded stainless steel.
|
$55Reg.$61
3PVP-WT3:
Use for through-the-wall installations. Fits between standard wall
studs. Comes with an insulation ring to reduce air infiltration where
the pipe slips through the thimble.
|
$57Reg.$62
3PVP-X4AD:
Use to attach to appliance outlet allowing for easy pipe connection.
Allows connection of 4” vent to 3” appliance outlet. Seal adapter to
appliance with high temperature sealant.
|
$17Reg.$23
3PVP-ADFF:
Use to connect PelletVent Pro to BioFlex when relining a masonry
chimney. Only approved for use with BioFlex.
|
$17Reg.$23
3PVP-ADFM:
Use to connect BioFlex to PelletVent Pro when relining a masonry
chimney. Only approved for use with BioFlex.
|
$32Reg.$37
PVP-FTC:
Use to connect PelletVent Pro rigid pipe to a masonry chimney with
stainless steel flexible relining. Female end swivels to allow ease
of connection.
|
$86Reg.$93
3PVP-TAD:
Use for a 90° offset. Attaches directly to appliance as an adapter.
Removeable twist-lock Clean-Out Tee Cap.
|
$2099Reg.$2699
3PVP-TADX4:
Use for a 90° offset. Attaches directly to appliance as an adapter.
Converts a 3” appliance to a 4” PelletVent Pro system. Removeable
twist-lock Clean-Out Tee Cap.
|
$19Reg.$23
3PVP-WS:
Use to support vent pipe or tee sections. Provides 1” clearance.
|
$22Reg.$26
3PVP-WSA:
Use to support vent pipe or tee sections. Adjusts to provide 1”- 3”
clearance.
|
$43Reg.$47
3PVP-CS:
Use to support pipe. May be used on flat ceilings. Painted black. Trim
and clamp included.
|
1
$5Reg.$7
3PVP-SC:
Use to maintain a weather tight resistant seal between the pipe and
the flashing.
|
$17Reg.$21
3PVP-F6:
Use to weather proof the penetration of vent pipe through the roof.
Storm Collar required. Select roof flashing based on pitch of roof.
For pitches of 0/12 - 6/12. For steep roof pitches, refer to the Type
B Gas Vent section.
|
$259Reg.$289
3PVP-25BF:
Use when relining masonry chimney for use with biofuel appliances.
Made of super-ferritic stainless steel. Must be used with PelletVent
Pro Male and Female Flex Adapters. Rigid pipe must be used when
terminating system.
|
$70Reg.$79
3PVP-X6:
Use to transition between PelletVent Pro to existing chimney such as
DuraTech, DuraPlus or DuraPlus HTC. Requires a DVL/ DuraBlack Chimney
Adapter to fasten into support box or wall thimble, for 6”, use
adapter 8674, for 8”, use adapter 8874.
|

|